Skip to main content

Boston commercial kitchen installation

Commercial Kitchen Equipment Installation in Boston

New units set, levelled, connected and started up correctly — for new kitchens, replacements and line changes across Greater Boston.

  • Site check before the unit arrives
  • Start-up and test run on install day
  • New kitchens and like-for-like replacements
Checked Site check first
Started Tested on install day
Local Greater Boston
Pre-Install Site Check
Start-Up and Test Run
New Kitchens and Replacements
Greater Boston Coverage
Installation

Equipment Installation

Installed right the first time, so the first service call is not a repair.

A surprising share of service calls on new equipment trace back to the day it was installed: a refrigerator pushed against a wall with no room for the condenser to breathe, a fryer that was never levelled, a dish machine fed water that never reaches the temperature it needs. Installation decides how the next ten years go.

BARO Service installs commercial kitchen equipment for restaurants, hotels, schools, hospitals and markets across Boston. Older buildings are the rule here rather than the exception — narrow stairs, basement kitchens, small freight elevators, rooftop access through a hatch — so we look at the route in before we look at the spot where the unit will stand.

Before install day we check the space, the clearances the manufacturer requires, ventilation, and the gas, electric, water and drain connections the unit needs. In Massachusetts these utility connections are licensed work and many installs need a permit, so we confirm who makes each connection well before the delivery truck arrives.

Call (617) 499-7575 with the model you are installing and where it is going. A site check before delivery costs far less than a unit that will not fit through the door.

Equipment we install

Refrigeration

Cooking

Warewashing and beverage

Replacements and line changes

  • Failed units replaced like-for-like
  • Equipment moved and reconnected during a remodel

Installation services

Three kinds of installation work.

Most installation calls are one of these. Each needs a different amount of planning.

01

New kitchens

  • Equipment set to the layout and flow of the kitchen.
  • Clearances, ventilation and access checked against the plan.
  • Every unit started and tested before opening day.
02

Replacements

  • A failed unit swapped for a new one with as little downtime as possible.
  • Connections checked — a new model often needs different ones.
  • The old unit disconnected and moved out of the way.
03

Connections and permits

Gas, electric, water and drain connections are licensed work in Massachusetts, and many need a permit. We confirm who makes each one before install day.

Preventive maintenance

Before install day

What we confirm before the unit arrives.

Most installation problems are visible a week before delivery. These six checks catch them.

1

The route in

Doors, stairs, elevators and corners measured against the crated unit. Old Boston buildings are rarely generous.

2

Clearances

The space the manufacturer requires around condensers, burners and vents — so the warranty stays valid.

3

Gas supply

Pipe size, pressure and shut-off location for the BTU rating the unit needs.

4

Electrical

Voltage, phase and a dedicated circuit with the right breaker.

5

Water and drain

Supply pressure, filtration, and a drain that meets code, air gap included.

6

Ventilation

Hood coverage for cooking equipment, and airflow for anything that rejects heat.

Why it matters

What a professional installation protects.

Equipment installed to the manufacturer’s specification runs the way it was rated, keeps its warranty and passes inspection. Equipment installed to “close enough” spends its whole life working harder than it should.

Code compliance

Clearances, ventilation and utility connections done to code, so the kitchen passes inspection the first time.

Rated performance

Levelled, connected and calibrated units reach rated temperature and recovery from the first service.

Safety

Gas connections leak-tested, electrical loads matched, safety controls verified before handover.

Kitchen flow

Placement that fits how the line actually works, not just where the unit happens to fit.

Installation process

Site check, install, start-up.

Planned so the kitchen loses as little time as possible.

  1. 1
    Site check Route, space, clearances and utilities checked against the unit's specification.
  2. 2
    Set and connect The unit is placed, levelled and connected, working alongside licensed trades where needed.
  3. 3
    Start-up and test Run through a full cycle, calibrated, and handed over with care instructions.

Why BARO

Why Boston kitchens trust BARO with installation.

The team that repairs equipment knows exactly what a bad installation costs.

Experience

We see what bad installs cause.

Repair work shows which installation shortcuts fail first — and we do not take them.

Planning

Checked before delivery.

Route, clearances and utilities confirmed before the truck is booked.

Start-up

Tested on install day.

Every unit is run, calibrated and checked against its rating before handover.

Afterwards

One team after the install.

Maintenance and repair from the people who installed it.

Boston service area

Equipment installation across Greater Boston.

Downtown, Back Bay, the South End and the Seaport, out to Cambridge and Somerville.

  • Downtown and the Financial District
  • Back Bay and the South End
  • North End and the Seaport
  • Fenway and Allston-Brighton
  • Cambridge and Somerville
  • Greater Boston

Planning an install? Call before delivery.

Call (617) 499-7575 with the model and the location. A site check before delivery saves the costly surprises.

Call Us (617) 499-7575
Call (617) 499-7575 Call BARO Service
Call Now Request Service